Best Audi A4 Stratmosphere Shortshifter Install
Title : Best Audi A4 Stratmosphere Shortshifter Install
link : Best Audi A4 Stratmosphere Shortshifter Install
Best Audi A4 Stratmosphere Shortshifter Install
Required tools:
1. 3/6mm allens (6mm allen should cause got an 8" reach)
2. Socket laid upwards alongside metric sockets, extension, ratchet 8mm as well as 10mm opened upwards halt wrench.
3. Circlip Pliers
4. Torx25 driver
5. Loctite (although non a tool, also non supplied but HIGHLY recommended)
6. Shop towels to wipe your hands gratis of grease!
7. H5N1 friend is a valuable tool to assist yous inward the install, although non required
also highly recommended.
Step 1: is to take the shift knob past times turning the knob counter clockwise till
the knob is off. Then carefully elevator upwards at the look betwixt the shifter assembly
cover as well as the middle console equally depicted past times the ruby arrows.
Step:2 With a 10mm socket wrench, take the 2 10mm nuts belongings the foam padded
sound break.
Step 3: You volition as well as then run across the amount of your shifter assembly. Now alongside your 6mm
allen wrench take the 2 bolts as well as the i metallic plate that connected the
shifter linkage to the transmission linkage. They are loctited from factory
and thence a measure allen wrench may non allow yous to supply plenty torque to
remove them. In this case, role a 6mm socket wrench adapter to take these bolts.
Step 4: With the 2 6mm bolts removed, loosen the forepart 2 10mm nuts belongings the
shifter "bucket". You create non involve to take these 2 nuts, only loosen.
Step 5:Completely take the bring upwards 2 10mm nuts. This volition allow yous to gain access
to the 4 torx bolts.
Step 6: CAREFULLY take the 4 torx bolts (T25) that concur the shifter assembly
down. Be careful to non drop/lose i of the bolts betwixt the shifter bucket
and the middle console.
Step 7: Once yous take the 4 torx bolts, function the shifter linkage gratis from
the transmission linkage (bottom arm). Once that's done it's easiest to larn the
assembly out past times pushing the lead house connectedness to the left equally shown as well as pulling
the linkage out. It mightiness accept some function to larn the assembly positioned to remove
it.
Step 8: With the shifter assembly out, accept your circlip pliers as well as take the
circlip that holds the linkage to the assembly.
Step 9: At the articulation where the bottom linkage connects to the upper linkage,
remove the 10mm nut/bolt belongings the linkage together. This volition allow yous to
remove the stock linkage from the assembly.
Step 10: Now take the 2 prophylactic dampers from the flexible pin cup, as well as then
remove the pin loving cup from the stock shifter linkage.
Step 11: Take the bundle of silicon grease as well as liberally apply to the ball.
Install the flexible pin loving cup to the Stratmosphere shifter linkage. Tie the
zip necktie unopen to the pin cup. You should detect a decrease of slop/play inward the
shifter. Do non over tighten.
Note: lay the side alongside the notches facing upwards away from the bearings. Reassemble
the dark dampers, the linkage should await similar the following.
When replacing the circlip retrieve to house the metallic spacer from the master copy assembly betwixt the damper as well as the circlip.
Step 12: Assemble the lower percentage of the linkage. Place i shim betwixt the
bearing as well as the lower linkage on each side(3 were included, yous exclusively involve 2)
Use a pen/small screwdriver to grade the shim as well as secure alongside the provided
bolt as well as locknut. Tighten until the bolt does non spin freely, but create non over tighten.
The assembled linkage should await similar the pic above. Note the position
of the lower linkage inward relations to the shifter arm. The hole is facing the
bottom. This is crucial during reassembly.
of the 4 aluminum spacers nether the ends of the 2 rails that concur the shifter
in place. Again live on careful to non lose a spacer. Tighten downwardly the 4 torx bolts
at this point.
Step 14: Reverse the disassembly process. First supersede the 2 10mm nuts at
the back, as well as tighten downwardly the 2 inward the forepart of the console. Now using the
unsupplied loctite yous purchased, house a modest amount on the thread of the
2 6mm bolts that connect the shifter linkage to the transmission linkage. This
is a very important measuring inward preventing the bolts from vibrating loose
over time. Now grade the shifter thence that the bottom linkage is easily accessible,
reinstall the plate as well as the bolt. Do non completely tighten the bottom 6mm bolt,
you volition adjust this afterward to ensure proper alignment of the assembly. Reinstall
the lead house 6mm bolt, over again create non tighten completely. Now alongside both bolts partially
tightened, align the shifter inward the grade sliding it forwards as well as dorsum until
it's sitting inward the grade yous desire it to be. Now tighten the 2 bolts (snug)
and reinstall your shift knob. With the engine OFF, examination that yous can
easily shift through each gear including reverse. Make certain that the distance
between shifting from neutral to third, as well as neutral to 4th is the same. If
you tin engage all gears easily, as well as the bottom linkage doesn't come upwards inward contact
with the shifter bucket, tighten downwardly the 2 6mm bolts completely. Now reinstall
the audio break, as well as the 2 10mm nuts that secure it. Carefully reinstall the
shifter cover/shift knob as well as accept your motorcar for a spin! You're done! Now how
hard was that???? *DON'T ANSWER THAT!* =)
Pictures used inward this how-to are of Alan's fingers as well as his gorgeous pearl white
A4.
Thus the article Best Audi A4 Stratmosphere Shortshifter Install
You are now reading the article Best Audi A4 Stratmosphere Shortshifter Install with the link address https://newaudisportscar.blogspot.com/2019/01/best-audi-a4-stratmosphere-shortshifter.html